Foamex Printing Company

A handwashing reminder is most useful when staff see it at the moment they need to act. In a food business, that means thinking about the flow of work: where people enter the kitchen, prepare ingredients, use sinks and move between different tasks. A sign hidden behind equipment or placed far from the relevant area can easily be overlooked. Walk through the workplace from a staff member’s point of view and identify the points where a short, clear reminder would help. This guide suggests practical locations and explains how to keep hygiene and emergency signs distinct. Follow the staff journey Start where staff enter food preparation areas. A reminder near the kitchen entrance can set expectations before work begins, especially if employees move between front-of-house and food handling tasks. Place it where people naturally pause or pass, rather than on a surface covered by notices, storage or equipment. The next useful location is beside the handwashing sink. A sign near the tap o...

Updating an exhibition stand does not always mean starting again from scratch. You may want to refresh a promotion, correct outdated information or bring the display in line with a new brand design. Before ordering replacement graphics, check how the existing stand is built and how its panels fit. Small differences in dimensions or layout can affect alignment across a wall, while the choice of material affects handling and storage. A careful review of the stand, artwork and installation method can help make the update fit smoothly into your event plans. Begin with the stand you already have First, identify the shell scheme system and the configuration of your stand. Note whether it has a single back wall, an L-shaped corner or a U-shaped layout. Check which panels sit between the frame poles and whether any existing graphics cover the poles for a continuous finish. Measure each section you plan to update. The supplied product page lists typical infill panels at 950 mm × 2,400 mm a...

Printed boards can travel through several hands before they are in place: packing, transport, unloading and installation all create opportunities for scuffs. At an exhibition, even a small mark may be noticeable on a large, clean graphic. A little preparation can help protect the print and edges while keeping setup straightforward. Check how the panels are packed, plan where they will be handled and decide how they will be mounted before the event day. The following steps draw on the supplied product information and practical setup considerations for temporary displays. Prepare the stand before unpacking Set up the shell scheme or display framework first. Clear the floor and nearby surfaces of tools, packaging and other items that could rub against a panel. Check the wall layout, required fixing method and panel order against the stand plan. This matters because the supplied product pages describe rigid boards intended to fit specific shell scheme arrangements. Some layouts use infill ...

A building site can change from one day to the next. Work areas move, new hazards appear and different people arrive on site, so clear signs help communicate what is happening and where people should go. The right set depends on the work, the site layout and the risks present; one standard bundle will not suit every project. Start by identifying the information workers, visitors and passers-by need at each location. Then choose signs that make those messages easy to recognise, place them where they can be seen and review them as the site changes. Start with the site entrance The entrance is a useful place to give people essential information before they enter the working area. Consider whether visitors need directions, a warning about site access or a reminder of required protective equipment. The supplied construction-sign page lists site entrance, keep-out and hard-hat signs among its examples. Walk the boundary and approach routes as if you were visiting for the first time. Check th...

A sign that hangs on or near a door can identify a room, share a message or help visitors find their way around a business. Before ordering, it helps to pin down exactly where the sign will sit and how people will see it. A door-mounted sign has different practical needs from a panel suspended high above an aisle, even if both are described as hanging signs. Check the dimensions, material, artwork and fixing method against the space, then confirm the finished specification with the supplier. These checks can help you avoid a sign that looks right online but does not suit its location. Decide what the sign needs to do Begin with the message. Is the sign identifying a meeting room, marking a department, displaying opening information or supporting a promotion? Keep the wording short enough to read quickly, especially if people will be passing through a doorway. Next, identify the exact position. A sign attached to a door, mounted beside it or suspended from an overhead structure will be ...

Seasonal promotions move quickly, so shop signage needs to catch attention while making the offer easy to understand. A banner in a window can announce a sale, highlight a new collection or give passers-by a reason to look inside. Its success depends on more than colour and wording: placement, visibility, size and the way it is fixed all matter. A projecting sign can also help shoppers identify a business as they approach along a busy street. Here’s how to plan these two types of retail signage around your shopfront and promotional calendar. Give each sign a clear job Start by deciding what shoppers should notice first. A window banner might communicate a seasonal offer, while a sign projecting from the building can help people find the shop from further along the street. Give each sign one main purpose and keep its message focused. For a promotion, put the key information first: the event or offer, followed by any essential dates or conditions. Use a type size that can be read fr...